PVC is everywhere in a house: drains, vents, irrigation, and some pool and well lines. It is tough, but a crack, a failed joint or a nail through the wall will still make it leak. The right fix depends on what the pipe carries, because a drain pipe that carries wastewater by gravity and a pressurized line are not the same problem.
A leaking PVC pipe can be stopped for now with a rubber or self-fusing silicone wrap, a repair clamp or two-part epoxy putty, but these are temporary. The permanent repair is to cut out the damaged section and fit a coupling with PVC primer and cement, after turning off the water and letting the pipe dry. Pressurized lines, pipes inside walls or under a slab, and leaks that return should be handled by a plumber.
- First work out what the pipe carries: wastewater (drain), or water under pressure (irrigation, supply).
- Wraps, clamps and epoxy buy time. They are not a permanent fix on a pressurized line.
- The lasting repair is cutting out the damaged section and joining new pipe with couplings, primer and PVC cement.
- Superglue and general adhesives are not a substitute for PVC cement.
- A leak inside a wall or under a slab is a job for a plumber.
Step 1: Stop the water and find the damage
Shut off the water to the pipe. For an irrigation line that is the zone or main valve. For a drain, stop using the fixture that feeds it. Dry the pipe and look closely. A hairline crack, a split along a seam, a joint that has pulled apart and a hole from a screw all need slightly different approaches.
Temporary fixes that work for a short time
These help you stop the damage until the proper repair is done.
- Rubber or self-fusing silicone tape. It is wrapped tightly with overlap, which stretches and bonds to itself. It can hold a small leak for a while, and it is more effective on drains than on pressure.
- Epoxy putty. A two-part putty is kneaded and pressed over a dry, clean crack and left to cure for the time on the label. It suits small cracks and pinholes.
- A pipe repair clamp. A rubber sleeve with a metal band, tightened over the leak. This is a sturdier temporary fix and also works on small holes.
- A fiberglass resin wrap. Activated by water, it sets hard around the pipe. Follow the manufacturer's instructions and wear gloves.
Treat each of these as a delay. Pressure, sun and ground movement will defeat them, and a failed patch can let go all at once.
What not to rely on
Household superglue, silicone caulk and duct tape are not suitable for a pipe that holds water. They may seem to work for a day. PVC joints are sealed with solvent cement, which chemically welds the pipe and fitting together, and nothing else behaves that way.
The permanent repair: replace the damaged section
- Turn off and drain the line. Water in the pipe stops the cement from bonding.
- Cut out the damaged section with a PVC cutter or fine-toothed saw, leaving clean square ends on healthy pipe.
- Deburr and dry-fit the new piece and a repair coupling, which has no internal stop so it slides over the gap. Mark the depth.
- Prime and cement. Apply PVC primer, then cement, to the pipe ends and fitting. Push together with a quarter turn and hold for the time on the can.
- Let it cure for the full time stated before turning the water on. Pressure testing a joint that has not cured is how repairs fail.
PVC cement and primer are strong chemicals. Work in a ventilated area and keep them away from flame.
When to stop and call a plumber
- The pipe is inside a wall, a ceiling or under the slab.
- It is a sewer line or the main drain leaving the house.
- The leak is on a pressurized line and keeps returning.
- The pipe is cracked in several places, which suggests ground movement or age.
- You are unsure what the pipe is, what it carries or where it goes.
A plumber can locate the damage without opening more of the wall than needed. Our pages on water pipe repair and leak detection explain how that is done, and a camera inspection can check the inside of a drain line.
Preventing the next leak
- Keep irrigation lines buried to the depth the system calls for, and protect exposed sections from impact and sun.
- Support horizontal drain pipes at the right intervals so they do not sag.
- Avoid driving fasteners near pipe runs in walls without checking where the pipes are.
- Wrap or drain exposed pipes before a cold snap. Our guide to pipe insulation covers where it matters in Houston.
Royal Flush Affordable Plumbing is licensed and insured. For PVC pipe repair it works under Texas Responsible Master Plumber License RMPL #42403, and agrees the price before work begins.
Frequently asked questions
Can I repair PVC without cutting it?
For a short time, yes, with a clamp, wrap or epoxy putty. For a lasting repair the damaged section is cut out and replaced.
Is superglue okay on PVC?
No. PVC pipe is joined with primer and solvent cement, which weld the pieces together. Household glues do not.
How long does PVC cement take to cure?
It depends on the pipe size, temperature and humidity, and the can lists the times. Wait for the full time before the pipe is pressurized.
Why does my PVC pipe keep leaking at the joint?
Common causes are a joint that was not primed or fully seated, movement in the pipe, a fitting under stress, or a pipe that has aged or been left in the sun.
When should I call a plumber for a PVC leak?
When the pipe is in a wall or slab, is a sewer or pressurized line, leaks more than once, or you cannot tell what it is.
